A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
Here down the page you can discover additional quality advice in relation to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old tub is easily available, the task can move quickly; if you need to open up a wall to eliminate the old tub and also position the new bathtub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will need an assistant to leave the old tub and also set in the brand-new one. Make sure you have qualified yourself for the task and fit attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to think about employing one before you begin. Opportunities are you might need an expert plumber to make tube links.
This article will certainly help you set up a new tub in your shower room if you have already bought a brand-new bathtub as well as do not need to transform the setup of your previous water system pipes.
Your tools and also material checklist must make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite problematic due to the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Safeguard the faucet in position with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind ought to be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the required setting. The wooden boards are helpful in equally spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub up until the level reviews level.
To install taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints and new pipework for leaks and tighten them if necessary. Load the bath tub as well as additionally examine the overflow electrical outlet and the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the tub needs to wait up until the tub has been used at the very least when as this will certainly settle it right into its last position.
Planning for the Installment
First of all, the sustaining framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in complications with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can fracture fairly early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently offered on the market. It is advisable to fit the tiles utilizing waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking time to browse our piece. Sharing is nice. Helping people is fun. Many thanks for going through it.
We're ready, dial now! Report this page